Shipboard Lighting
Shipboard lighting systems must operate reliably in electrical and environmental conditions that are far more demanding than standard commercial applications. When the US Navy moved towards solid-state LED lighting, the requirement was not only to improve efficiency and reduce maintenance. The new LED drivers also had to fit into existing shipboard fixtures, support established brightness-control methods and meet demanding military and naval specifications. POWERBOX developed rugged, long-life LED drivers for shipboard use, combining electrical compatibility mechanical integration and compliance with key naval requirements.
The challenge
The transition from legacy lighting to solid-state LED technology offered clear advantages, including lower power consumption, longer operating life and reduced maintenance. However, the upgrade also introduced several engineering challenges.
Existing naval lighting installations were built around established fixture designs and electrical interfaces. Replacing these systems could not require major structural changes, rewiring or modification of the vessel. The new LED driver solution therefore had to integrate with the existing mechanical footprint while supporting the same operational brightness-control methods used by the ship’s crew.
Traditional shipboard lighting technologies also brought practical limitations, including short lamp life, high maintenance demand, long warm-up times for high pressure sodium fixtures and the environmental concerns associated with mercury-based fluorescent lighting.
To enable a practical upgrade path, the replacement solid-state lighting system required an LED driver capable of managing three independent AC power inputs. This allowed the driver to support multiple brightness levels from a single LED array, replacing the previous multi-bulb approach while maintaining compatibility with existing shipboard control methods.
The solution
To survive the rigorous demands of naval deployments, Powerbox engineered a series of ultra-rugged, highly efficient, and environmentally sealed custom LED drivers. The internal power electronics are designed for continuous operation under extreme thermal fluctuations, high vibration, and severe mechanical shock. The completed hardware platform was subjected to rigorous laboratory verification to achieve full compliance with essential military standards:
- → MIL-DTL-16377 Compliance: Adhering strictly to the general specifications governing naval lighting fixtures, internal support components, shock-resistant lenses, and associated shipboard auxiliary hardware systems.
- → MIL-STD-461 Electromagnetic Control: Meeting stringent military thresholds for electromagnetic interference (EMI), suppressing both radiated and conducted emissions to guarantee zero interference with sensitive shipboard communications, radar, and sonar suites.
- → MIL-STD-1399/300A Interface Standards: Engineering specific power-factor correction and transient voltage protection to handle the rigorous electrical tolerances, harmonic distortions, and spikes typical of shipboard AC power grids.
These custom power supplies satisfy all legacy electrical interfaces, eliminating the need for expensive structural rewiring or hull modifications during scheduled drydock overhauls.
Added value
Integrating Powerbox’s custom defense power solutions alongside solid-state lighting arrays eliminates the frequent component failures common to legacy systems, while delivering clear, measurable advantages to fleet logistics and vessel efficiency:
- → Elimination of Hazardous Materials: Removing mercury-dependent components from active vessels mitigates crew exposure risks and completely eliminates complex, hazardous waste storage and disposal regulations at port.
- → Drastic Maintenance Reduction: Extending the operational lifespan of shipboard illumination reduces daily maintenance overhead, freeing up engineering personnel and vastly simplifying warehouse inventory supply chains by eliminating the need to stock high volumes of delicate replacement bulbs.
- → Enhanced Fuel Efficiency: Minimizing power consumption across thousands of active lighting nodes significantly lowers the aggregate auxiliary electrical load on the shipboard grid, directly reducing generator workloads and conserving fuel during extended long-range deployments.
Beyond shipboard solid-state lighting arrays, Powerbox designs custom power conversion architectures across multiple highly regulated sectors. Explore our specialized solutions for harsh, mission-critical environments including rugged defense electronics, high-availability medical systems, and robust industrial power applications.
Please contact a power conversion specialist with your need today.
Compact power for oil and gas leakage monitoring
Reducing size and weight on a power system including back-up, communications interface and previous generation compatibility, for operation in challenging environment.
The Medical Device and Manufacturing Expo
The Medical Device and Manufacturing Expo
Anaheim, CA, USA
Feb 10-12, 2015
Converter request results in system optimization
The customer’s Challenge was to secure drivers communication for a period of six hours at flat vehicle battery conditions.
Airborne Multi Platform Mission Computer-System
The challenge was to reduce the size and weight of the power solution, since this is an airborne product and reach competitive price points as manufactured in relatively high volume for the defense market.
Simplicity makes next-generation power converter for rail industry run at 93% efficiency
One of Europe’s largest power supply companies, Powerbox , introduces the next generation of innovative power converters.
Vicor and Powerbox strengthen Distribution Partnership in Europe
Vicor and Powerbox-Craftec, Europe ́s leading power distributor have signed a long-term partnership agreement for Pan European Distribution.
Cosel expands 30W, 60W and 90W of Din rail Power Supplies
Cosel Co. Ltd has announced the expansion of the KH series DIN Rail Power Supplies.
